Home ›› Industrial Communication ›› Wireless Access Point/Router

O-IAP-120/120+

Industrial IEEE 802.11 b/g wireless access point

Features

  • High Speed Air Connectivity: WLAN interface support up to 54Mbps link speed
  • Support X-Roaming < 100 ms
  • Support wireless load balance
  • Highly Security Capability: WEP/WPA/WPA-PSK(TKIP,AES)/ WPA2/WPA2-PSK(TKIP,AES)/802.1X Authentication supported
  • Support AP/Bridge/Repeater/AP-Client Mode
  • Switch Mode Supported: Daisy Chain support to reduce usage of switch ports
  • Dual redundant Ethernet port support redundant mode (Recovery time < 10ms)
  • Secured Management by HTTPS
  • Event Warning by Syslog, Email, SNMP Trap, Relay and Beeper
  • Rigid IP-30 housing design
  • DIN-Rail and panel mounting enabled

Specification

  IAP-120 IAP-120+
Physical Ports    
10/100Base-T(X) Ports in RJ45 Auto MDI/MDIX                                                                                     2
P.O.E. PD port Present at ETH2
Fully compliant with IEEE 802.3af   Power
Device specifi cation
Over load & short circuit protection
Isolation Voltage: 1000 VDC min.
Isolation Resistance : 108 ohms min
WLAN interface    
Operating Mode AP/Bridge/Repeater/AP-Client
Antenna and connector 2dBi antenna on reverse SMA connector
Radio Frequency Type DSSS, OFDM
Modulation IEEE802.11b : CCK, DQPSK, DBPSK
IEEE802.11g : OFDM with BPSK, QPSK, 16QAM, 64QAM
Frequency Band
America/FCC : 2.412~2.462 GHz (11 channels)
Europe CE/ETSI : 2.412~2.472 Ghz (13 channels)
Transmission Rate IEEE802.11b : 1/ 2/ 5.5/ 11 Mbps
IEEE802.11g : 6/ 9/ 12/ 18/ 24/ 36/ 48/ 54 Mbps
Transmit Power IEEE802.11b/g : 20dBm Max
Receiver Sensitivity -81dBm @ 11Mbps, PER< 8%;
-64dBm @ 54Mbps, PER< 10%
Encryption Security WEP : (64-bit ,128-bit key supported)
WPA :
WPA2 : 802.11i(WEP and AES encryption)
PSK (256-bit key pre-shared key supported)
802.1X Authentication supported
TKIP encryption
Wireless Security SSID broadcast disable
Protocol Support    
Protocol ARP, BOOTP, DHCP, DNS, HTTPs, IP, ICMP, SNTP, TCP, UDP, RADIUS, SNMP, STP (IEEE 802.1D)
LED Indicators    
Power Indicator PWR 1(2)(P.O.E.) / Ready :
Red On : Power is on and booting up.
Green On : Power is on and functioning Normally.
10/100TX RJ45 Port Indicator Green for port Link/Act at 100Mbps. Amber for port Link/Act at 10Mbps
WLAN LEDs WLAN Link /ACT : Green
WLAN Strength : 1<25%, 2<50%, 3<75%, 4<100%
Fault Red : Ethernet link down or power down
Fault contact    
Relay Relay output to carry capacity of 1A at 24VDC
Power    
Redundant Input Power Dual DC inputs. 12-48VDC on 6-pin terminal block Triple DC inputs, 48VDC from PoE and Dual 12~48VDC on 6-pin terminal block
Power Consumption (Typ.) 6 Watts
Overload Current Protection Present
Reverse Polarity Protection Present on terminal block
Physical Characteristic    
Enclosure IP-30
Dimension (W x D x H) 54.2(W) x 106.1(D) x 145.4(H) mm (2.13x4.18x5.72 inch.)
Weight (g) 800 g 804 g
Environmental  
Storage Temperature -40 to 85°C (-40 to 185°F)
Operating Temperature -10 to 70°C (14 to 158°F)
Operating Humidity 5% to 95% Non-condensing
Regulatory approvals    
EMI FCC Part 15, CISPR (EN55022) class A
EMS EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS),EN61000-4-8, EN61000-4-11
Shock IEC60068-2-27
Free Fall IEC60068-2-32
Vibration IEC60068-2-6
Safety EN60950-1
MTBF (Hours) (MIL-HDBK-217F2, GB, GC, 25°C ) 352,982 352,594
Warranty 3 years

Have Questions? Call +603 7887 6820 or email sales@anewtech.com.my