Home ›› Industrial Communication ›› Wireless Access Point/Router

O-IAP-420 / IAP-420+

Industrial IEEE 802.11 b/g/n wireless access point with 2x10/100Base-T(X)

Features

      O-IAP-420 O-IAP-420+
    Physical Ports    
    10/100Base-T(X) Ports in RJ45 Auto MDI/MDIX                                                                                     2
    P.O.E. PD port   Present at ETH2
    Fully compliant with IEEE 802.3af  Power Device specifi cation
    Over load & short circuit protection
    Isolation Voltage : 1000 VDC min.
    Isolation Resistance : 108 ohms min
    WLAN interface    
    Operating Mode AP/Bridge/AP-Client
    Antenna Connector 1 x External reverse SMA-type antenna connector
    Radio Frequency Type DSSS, OFDM
    Modulation IEEE802.11b: CCK, DQPSK, DBPSK
    IEEE802.11g/n: OFDM with BPSK, QPSK, 16QAM, 64QAM
    Frequency Band America/FCC: 2.412~2.462 GHz (11 channels)
    Europe CE/ETSI: 2.412~2.472 Ghz (13 channels)
    Transmission Rate 802.11b: 1/2/5.5/11 Mbps
    802.11g: 6/9/12/18/24/36/48/54 Mbps
    802.11n(40MHz): UP to 150 Mbps
    Transmit Power 802.11b: 13.5dBm ±1.5dBm
    802.11g: 13.5dBm ±1.5dBm
    802.11n(2.4G@20MHz): 13.5dBm ±1.5dBm
    802.11n(2.4G@40MHz): 13.5dBm ±1.5dBm
    Receiver Sensitivity 802.11b: -90dBm ±2dBm@1Mbps
    802.11g: -72dBm ±2dBm@54Mbps
    802.11n(2.4G@40MHz,MCS7): -68dBm ±2dBm
    Encryption Security WEP: (64-bit, 128-bit key supported)
    WPA/WPA2:802.11i (WEP and AES encryption)
    WPA-PSK (256-bit key pre-shared key supported)
    802.1X Authentication supported
    TKIP encryption
    Wireless Security SSID broadcast disable and enable
    Protocol Support    
    Protocol ARP,BOOTP, DHCP, DNS, HTTP, IP, ICMP, SNTP, TCP, UDP, 802.1X, SNMP, STP
    LED Indicators    
    Power Indicator LED x 3, PWR 1, 2, (PoE):
    Green On: Power is on and functioning Normally.
    100/1000TX RJ45 Port Indicator LED x 2 , Green for port Link/Act at 100Mbps.
    WLAN LEDs WLAN Link /ACT: Green: Link,
    Power    
    Redundant Input Power Dual DC inputs.  12~48VDC on 4-pin terminal block
    Power Consumption (Typ.) 4watts
    Overload Current Protection Present
    Reverse Polarity Protection Present
    Physical Characteristic    
    Enclosure IP-30
    Dimension (W x D x H) 196(W) x 125(D) x 62.9(H) mm (7.72 x 4.92 x 2.48 inch.)
    Weight (g) 292 297
    Environmental  
    Storage Temperature -40 to 85°C (-40 to 185°F)
    Operating Temperature -10 to 60oC (14 to 140oF)
    Operating Humidity 5% to 95% Non-condensing
    Regulatory approvals    
    EMI FCC Part 15, CISPR (EN55022) class A
    EMS EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS),EN61000-4-8, EN61000-4-11
    Shock IEC60068-2-27
    Free Fall IEC60068-2-31
    Vibration IEC60068-2-6
    Safety EN60950-1
    Warranty 3 years

    anewtech-industrial-wireless-access-point-o-iap-420
    O-IAP-420 / O-IAP-420+ series are reliable 802.11 b/g/n WLAN Access Point with 2 ports LAN, provide wireless communication on industrial network. It supports 802.1X and MAC filters for security control. It can be configured to operate in AP/Bridge/Repeater/AP-Client mode.

    O-IAP-420 / O-IAP-420+ series are able to configure by WEB interface via LAN port or WLAN interface. O-IAP-420+ provides P.D. feature on ETH2 which is fully compliant with IEEE802.3af PoE P.D. specification.

Specification

  O-IAP-420 O-IAP-420+
Physical Ports    
10/100Base-T(X) Ports in RJ45 Auto MDI/MDIX                                                                                     2
P.O.E. PD port   Present at ETH2
Fully compliant with IEEE 802.3af  Power Device specifi cation
Over load & short circuit protection
Isolation Voltage : 1000 VDC min.
Isolation Resistance : 108 ohms min
WLAN interface    
Operating Mode AP/Bridge/AP-Client
Antenna Connector 1 x External reverse SMA-type antenna connector
Radio Frequency Type DSSS, OFDM
Modulation IEEE802.11b: CCK, DQPSK, DBPSK
IEEE802.11g/n: OFDM with BPSK, QPSK, 16QAM, 64QAM
Frequency Band America/FCC: 2.412~2.462 GHz (11 channels)
Europe CE/ETSI: 2.412~2.472 Ghz (13 channels)
Transmission Rate 802.11b: 1/2/5.5/11 Mbps
802.11g: 6/9/12/18/24/36/48/54 Mbps
802.11n(40MHz): UP to 150 Mbps
Transmit Power 802.11b: 13.5dBm ±1.5dBm
802.11g: 13.5dBm ±1.5dBm
802.11n(2.4G@20MHz): 13.5dBm ±1.5dBm
802.11n(2.4G@40MHz): 13.5dBm ±1.5dBm
Receiver Sensitivity 802.11b: -90dBm ±2dBm@1Mbps
802.11g: -72dBm ±2dBm@54Mbps
802.11n(2.4G@40MHz,MCS7): -68dBm ±2dBm
Encryption Security WEP: (64-bit, 128-bit key supported)
WPA/WPA2:802.11i (WEP and AES encryption)
WPA-PSK (256-bit key pre-shared key supported)
802.1X Authentication supported
TKIP encryption
Wireless Security SSID broadcast disable and enable
Protocol Support    
Protocol ARP,BOOTP, DHCP, DNS, HTTP, IP, ICMP, SNTP, TCP, UDP, 802.1X, SNMP, STP
LED Indicators    
Power Indicator LED x 3, PWR 1, 2, (PoE):
Green On: Power is on and functioning Normally.
100/1000TX RJ45 Port Indicator LED x 2 , Green for port Link/Act at 100Mbps.
WLAN LEDs WLAN Link /ACT: Green: Link,
Power    
Redundant Input Power Dual DC inputs.  12~48VDC on 4-pin terminal block
Power Consumption (Typ.) 4watts
Overload Current Protection Present
Reverse Polarity Protection Present
Physical Characteristic    
Enclosure IP-30
Dimension (W x D x H) 196(W) x 125(D) x 62.9(H) mm (7.72 x 4.92 x 2.48 inch.)
Weight (g) 292 297
Environmental  
Storage Temperature -40 to 85°C (-40 to 185°F)
Operating Temperature -10 to 60oC (14 to 140oF)
Operating Humidity 5% to 95% Non-condensing
Regulatory approvals    
EMI FCC Part 15, CISPR (EN55022) class A
EMS EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS),EN61000-4-8, EN61000-4-11
Shock IEC60068-2-27
Free Fall IEC60068-2-31
Vibration IEC60068-2-6
Safety EN60950-1
Warranty 3 years



Have Questions? Call +603 7887 6820 or email sales@anewtech.com.my