Home ›› Serial & Wireless Connectivity ›› Wireless Sensor and Camera

XBee-Pro® ZigBee Adapters

ZigBee Adapters for Serial and USB Devices


  • Supports the ZigBee PRO feature set
  • ZigBee® wireless connectivity for RS232, 485, and USB devices
  • Compatible with XBee gateways and modules
  • Outdoor RF line-of-sight range up to 1 mile with XBee-PRO®


RF Data Rate 250 kbps
Indoor/Urban Range Up to 300 ft (90 m) / 200 ft (60 m) Int’l variant
Outdoor/RF Line-of-Sight Range Up to 2 miles (3200 m) / 5000 ft (1500 m) Int’l variant
Transmit Power 63 mW (+18 dBm) Int’l version
Receiver Sensitivity (1% PER) -102 dBm
Antenna Type XBee ZB Adapters: Internal Antenna; XBee-PRO ZB Adapters: External RPSMA Antenna
Frequency Band 2.4 GHz
Serial Data Interface RS-232 DB9M/DTE or RS-485 (6-position wire terminal block) switch selectable between RS-422 half-duplex,
RS-422 full duplex and RS-485
USB Data Interface USB 2.0 Full Speed (with ESD protection); connects to host via captive 1-meter cable
Analog IO (AIO) &
Digital IO (DIO)
6-position wire terminal block; Analog IO: 0 - 10V, 4 - 20 mA, or +/- 2VDC Differential;
Digital IO: Digital Input or sinking driver output
Networking & Security
Network Topologies Point-to-point, Point-to-multipoint, Mesh
Number of Channels 14
Spread Spectrum Type Direct Sequence Spread Spectrum
Filtration Options PAN ID, 64-bit MAC, channel
Addressing 65,000 available addresses for each channel
LEDs Power: Glows green when external power is supplied (not active when battery powered to limit power drain)
Associate: Blinks when unit is connected and associated on an RF network
Controls Device reset (internal push button); Identification (internal push button) – relays ID to gateway
Dimensions (L x W x H) & Weight RS-232, RS-485, AIO, DIO models: 3.60 in x 1.90 in x 1.20 in (9.14 cm x 4.82 cm x 3.04 cm) 2.29 oz (64.92 g)
USB models: 2.87 in x 1.80 in x 0.83 in (7.29 cm x 4.57 cm x 2.10 cm) 1.60 oz (45.36 g)
Operating Temperature -40° C to +70° C
Power Requirements
Input Voltage RS-232, RS-485, AIO, DIO models: 3.7-6VDC and 9-30 VDC
USB models: Bus powered (+5V)
Power Consumption USB: 70 mA Rx and 250 mA Tx (normal operation) / 200 uA (suspend mode)
Regulatory Approvals
Emissions FCC Part 15.247, IC, ETSI/CE, Telec, EN55022 (Class B)
Safety UL60950, CAN/CSA C22.2 No.60950
RoHS Yes

XBee-PRO ZigBee adapters deliver wireless connectivity to electronic devices through advanced mesh networks. These adapters utilize the ZigBee PRO Feature Set, for robust self-healing, self-configuring networks. They are ideal for wirelessly enabling sensors, controllers and other devices in legacy wired applications, or where a common hardware interface is preferable.

XBee-PRO ZigBee adapters can be battery or mains powered. They are available in a wide range of physical interfaces, including RS-232, RS-485, USB (power harvesting), digital I/O and analog I/O. Built upon XBee-PRO modules, these adapters can be purchased in a broad range of configurations and customized to meet your application needs.

XBee adapters are compatible with ConnectPort® X gateways, XBee® modules and XBee accessories. This family of hardware, software and management tools provides users with unparalleled flexibility and end-to-end communication between devices.

Have Questions? Call +603 7887 6820 or email sales@anewtech.com.my